Renault Megane, Scenic

Since 1996 of release

Repair and car operation



Reno Megan, Stsenik
+ Cars of mark Renault Megane
+ Maintenance service
+ Engine repair
+ System of cooling, heating
+ Power supply systems, release
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
- Suspension bracket and steering
   Removal and installation of assemblage of a forward rotary fist
   Check and replacement of bearings of a nave of a forward wheel
   Removal and installation of a forward rack
   Partition of a forward rack
   Removal and installation of the forward stabilizer of cross-section stability
   Removal, partition and installation of the bottom lever of a forward suspension bracket
   Removal and installation of the spherical hinge of the bottom lever of a forward suspension bracket
   Check and replacement of bearings of a nave of a back wheel
   Removal, check and installation of the back shock-absorber
   Removal and installation of the back stabilizer of cross-section stability (back axis of the closed type)
   Removal and installation of a back axis
   The general description of a partition of a back axis
   Check and adjustment of a road gleam of the car
   Removal and steering wheel installation
   Removal, survey and installation of a steering column
   Removal, survey and installation of the steering mechanism
   Removal and installation of the pump of the steering hydraulic booster
   Prorolling of hydrosystem of the steering hydraulic booster
   Replacement of a protective cover of the steering mechanism
   Removal and installation of a tip of steering draught
   Removal and installation of cross-section steering draught
   Corners of installation of wheels
+ Body
+ Onboard electric equipment
+ Electric equipment schemes
3bf7a351




Partition of a forward rack

The suitable stripper of springs preferably regulated is required. Attempt to disassemble a rack without this tool will lead to damage of components or a trauma.

The new nut of a plate of the top fastening is required. Following procedures concern all models, except 2.0 l of the Compartment with 16 valves on which forward racks are attached in another way; components are located in a following order: a plate of the top fastening, the bearing, the top support, a cover and a spring.

 PARTITION

1. Clean off from a rack an external dirt, then tighten it vertically in a vice. Establish a stripper and compress a spring so to remove its pressure from support (address to an accompanying illustration).

2. Uncover a nut of a plate of the top fastening, then ослабьте a nut, having blocked a rod of the piston of the shock-absorber a suitable face key-shestigrannikom (address to an accompanying illustration).

3. Turn away a nut and remove a plate of the top fastening (address to an accompanying illustration).

4a. Remove a spring.

4b. Remove its bottom support.

4c. Remove the bearing then remove from the piston a dustproof cover (address to illustrations).

5. Examine the shock-absorber on presence of smudges. Check up a piston rod on presence of dot corrosion, and the shock-absorber case - on presence of damages. Keep the shock-absorber in vertical position and check up its work, some times having moved the piston at first at full capacity, and then on shorter distance (50-100 mm). In both cases resistance should be equal and identical. If the piston moves jerky or elasticity of the shock-absorber at check performance varied, and also if there is any visible sign of deterioration, replace a rack.
6. Examine other components on presence of damages, giving particular attention to the bearing, and replace them as required.
7. Establish a dustproof cover on the piston.
8. Establish the bearing, and then assemblage of the bottom support of a spring.
9. Establish a spring so that its former end rested against the terminator on a support.

10. Establish a plate of the top fastening, having combined its terminator with the spring end, then screw a new nut (address to an accompanying illustration). Block a rod of the piston of the shock-absorber and tighten a nut of an assembly plate the effort resulted in Specifications. Establish on a nut a cap.

11. Slowly let out and remove a stripper of springs, trying not to displace the spring ends.
12. Establish a rack on the car as Removal and installation of a forward rack is described in Section.