Renault Megane, Scenic

Since 1996 of release

Repair and car operation



Reno Megan, Stsenik
+ Cars of mark Renault Megane
+ Maintenance service
+ Engine repair
+ System of cooling, heating
- Power supply systems, release
   + Fuel and an exhaust system - petrol models
   - Fuel and exhaust systems - diesel models
      Removal and installation of a casing of the air filter
      Removal and installation of the gauge of a stock of fuel
      Removal and installation of a fuel tank
      Removal, installation and adjustment of a rope of gas
      Removal and installation of a pedal of gas
      Pouring and prorolling of fuel system
      Check and adjustment of the maximum turns of the engine
      Removal, installation, check and adjustment of a thermodrive and rope of fast idling
      Removal, installation, check and adjustment of components of system of fast idling
      Check, removal and installation of the proof-reader of the moment of injection at cold start
      The description, removal and valve installation отсечки fuel
      Removal and installation of the gauge of temperature of fuel
      Removal and installation of the fuel pump
      Methods of check and adjustment of the moment of injection
      Check and adjustment of the moment of injection
      Check, removal and installation of atomizers
      Removal and installation of the inlet pipeline and final collector
      Check and adjustment of turns of idling and delay turns
      turbocharger - the description and precautions
      Removal and installation турбокомпрессора
      Survey and service турбокомпрессора
      Removal and installation интеркулера (models with turbocharger)
      The general description and replacement of components of final system
   + Systems of decrease in toxicity of the fulfilled gases
+ Engine electric equipment
+ Coupling
+ Transmission
+ Power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment
+ Electric equipment schemes
3bf7a351




Removal and installation of the gauge of a stock of fuel

ТЕПЛОИЗОЛЯЦИОННЫЕ BOARDS

 REMOVAL

1. Disconnect a cable of weight from the battery (address to the Head an engine Electric equipment).

If the autoradio tape recorder in your car is coded before to disconnect the battery, be convinced that you know a code.

2. Remove a back seat or a pillow of a back seat as it is described in the Head the Body to get access to a cover of the gauge of a stock of fuel.
3. By means of a screw-driver accurately remove a plastic cover from a floor to get access to the gauge of a stock of fuel.
4. Disconnect a socket of electroconducting from the gauge and attach a socket to a car body to prevent its falling for a tank.
5. Note an arrangement of fuel hoses; a green hose on a left-hand side - fuel giving in an impellent compartment, and a red hose near to an electroconducting socket - fuel return (arrows on pump top specify a stream direction). Disconnect both hoses from the top part of the pump, then закупорьте the ends of hoses to minimise fuel loss.
6. Notice a direction of arrows on a cover of the gauge of a stock of fuel and a fuel tank, turn away blocking ring and remove it from a tank.
7. Accurately take assemblage of the gauge from a fuel tank, trying not to damage the lever. Remove a rubber sealing ring and check up its condition. If the sealing ring is unsuitable to operation, get the new.
8. Pay attention that the gauge of the index of a stock of fuel is accessible only as full assemblage - separate components are not on sale.


 INSTALLATION

1. Be convinced that the filter of a reception tube is not littered. Establish a sealing ring on the top part of a fuel tank.
2. Accurately enter assemblage of the gauge of a stock of fuel into a fuel tank.
3. Combine an arrow on a cover of the gauge with an arrow on a fuel tank (the arrow should be directed to a back part of the car), then establish blocking ring. Reliably tighten blocking ring, then repeatedly check up, that labels on a cover of the pump and a tank remained combined.

If there is a suitable head, tighten blocking ring the effort resulted in Specifications.

4. Connect submitting and returnable hoses to the top part of the gauge.
5. Connect electroconducting.
6. Connect the accumulator and start the engine. Check up submitting and returnable hoses of the gauge of a stock of fuel on leaks.
7. Establish a plastic cover and a pillow of a back seat.